support@flyingrobot.co.za
support@flyingrobot.co.za
Save up to 0%
Save %
Upgrading your drone has never been easier! Simply swap the props of your DJI Air 2S and within seconds you get up to 4% more flight time and up to...
View full details
Save 17%
Save %
NEXT GENERATION UPGRADE PROPELLERS for your DJI Mavic 3 and Mavic 3 Cine. Exceptional quality, low-noise and long flight time operation. Improved...
View full details
Save 0%
Save %
Matek anti-vibration bobbins for Flight Controllers M3 x 7mm + 4.5mm 4pcs
Save 0%
Save %
CAN-L4-3100 is a professional grade CAN Magnetometer based on RM3100 & ArudPilot AP_Periph firmware. RM3100 sensor technology provides high re...
View full details
Save 0%
Save %
The Mateksys CAN-L431 is an Adapter Node based on ArudPilot AP_Periph firmware. With this board, you can easily utilize the ArduPilot driver li...
View full details
Save 0%
Save %
CAN-L4-RC is an Adapter Node based on ArudPilot AP_Periph firmware. Using this adapter to turn Serial receiver into CAN receiver. Specifications ...
View full details
Save 0%
Save %
Features Wide 9V to 55V Operating Input Range with TVS protection 3x Output voltage options, 5.2V, 8V or 12V. Default 5.2V. Synchronous switchin...
View full details
Save 0%
Save %
CRSF-PWM Converter, CRSF-PWM-6 Compatible with CRSF protocol receiver only Support any CRSF protocol receivers (including 433MHz, 868MHz, 915MHz, ...
View full details
Save 0%
Save %
Specifications Sensor: All sensors DLVR-L10D, Industrial temperature range DLVR-L10D Sensor datasheet, pls visit www.allsensors.com Interface:...
View full details
Save 0%
Save %
The Mateksys Digital Airspeed Sensor ASPD-4525 features a ASPD-4525 sensor board, JST-GH to JST-GH 20cm silicon cable, pitot tube and a clear sili...
View full details
Save 0%
Save %
The Matek 1.2-1.3Ghz Antenna is one of the most durable and well-made antenna designs on the market today. When you use it we are confident you wi...
View full details
Save 0%
Save %
Specifications MCU: 168MHz STM32F405RGT6 IMU: ICM42688-P (SPI) Baro: SPL06-001 (I2C) OSD: AT7456E (SPI) Blackbox: MicroSD slot (SPI) 6x UARTs, 1x...
View full details
Save 0%
Save %
The MATEKSYS F405-VTOL Flight Controller features 25x25 and 35x35 mounting patterns and weighs 25g. It features a Barometer, BlackBox MicroSD, 6...
View full details
Save 0%
Save %
FC Specifications MCU: STM32F405RGT6, 168MHz , 1MB Flash IMU: ICM42688-P Baro: SPL06-001 OSD: AT7456E Blackbox: 16M Flash 5x UARTs, 1x Softserial...
View full details
Save 0%
Save %
4x Matek FC Anti Vibration Standoffs M2
Save 0%
Save %
The new features of F405-mini TE compared with F722-mini SE(EOL) F405 has 1MB flash which can run with ArduPilot. even with INAV firmware, some ...
View full details
Save 0%
Save %
M9N-5883 uses multi-constellation GNSS powered by u-blox NEO-M9N , NEO-M9N is a concurrent GNSS receiver which can receive and track multiple GNS...
View full details
Save 0%
Save %
Matek's H743-WING V3 Flight Controller arrives with new features and improvements over the original. This FC features a STM32H743VIT6 MCU running ...
View full details
Save 0%
Save %
The Matek H7A3-SLIM Flight Controller features STM32H7A3VI, ICM20602 & MPU6000, DPS310, OSD, 7x UARTs, 2x I2C, 1xCAN, 13x PWM outputs, BEC5V an...
View full details
Save 0%
Save %
Specifications Hall effect current sensor No voltage drop and heat on current sensor components Offset and Sensitivity are calibrated in factory C...
View full details
Save 0%
Save %
Get the voltage you need with this Matek BEC, convert 6-25V to either 5V, 9V, or 12V. This BEC defaults to 5V, select either 9V or 12V by solderin...
View full details
Save 0%
Save %
PDB Input voltage range: 6~60V (2~12S LiPo) PDB/current sense resistor: 140A cont, 264A burst. ESC power pads: 60A cont. 100A burst 6x ESC power /s...
View full details