Products

CRSF-PWM Converter, CRSF-PWM-6 Compatible with CRSF protocol receiver only Support any CRSF protocol receivers (including 433MHz, 868MHz, 915MHz, ...

The Matek 1.2-1.3Ghz Antenna is one of the most durable and well-made antenna designs on the market today. When you use it we are confident you wi...

Specifications MCU: 168MHz STM32F405RGT6 IMU: ICM42688-P (SPI) Baro: SPL06-001 (I2C) OSD: AT7456E (SPI) Blackbox: MicroSD slot (SPI) 6x UARTs,  1x...

The MATEKSYS F405-VTOL Flight Controller features 25x25 and 35x35 mounting patterns and weighs 25g. It features a Barometer, BlackBox MicroSD, 6...

FC Specifications MCU: STM32F405RGT6, 168MHz , 1MB Flash IMU: ICM42688-P Baro: SPL06-001 OSD: AT7456E Blackbox: 16M Flash 5x UARTs,  1x Softserial...

4x Matek FC Anti Vibration Standoffs M2

The new features of F405-mini TE compared with F722-mini SE(EOL) F405 has 1MB flash which can run with ArduPilot.  even with INAV firmware, some ...

M10-5883 uses multi-constellation GNSS powered by u-blox MAX-M10S. MAX-M10S supports concurrent reception of four GNSS (GPS, GLONASS, Galileo, and...

M9N-5883 uses multi-constellation GNSS powered by u-blox NEO-M9N , NEO-M9N is a concurrent GNSS receiver which can receive and track multiple GNS...

M10-L4-3100 is based on ArudPilots’ AP_Periph firmware,  It is a GNSS+COMPASS+BAROMETER peripheral with CAN/DroneCAN and UART/MSP interfaces. M10-...

The Matek H743-SLIM Flight Controller features STM32H743VI, ICM20602 & MPU6000, DPS310, OSD, 7x UARTs, 2x I2C, 1xCAN, 13x PWM outputs, BEC5V an...

Matek's H743-WING V3 Flight Controller arrives with new features and improvements over the original. This FC features a STM32H743VIT6 MCU running ...

Specifications Hall effect current sensor No voltage drop and heat on current sensor components Offset and Sensitivity are calibrated in factory C...

Get the voltage you need with this Matek BEC, convert 6-25V to either 5V, 9V, or 12V. This BEC defaults to 5V, select either 9V or 12V by solderin...

PDB Input voltage range: 6~60V (2~12S LiPo) PDB/current sense resistor: 140A cont, 264A burst. ESC power pads: 60A cont. 100A burst 6x ESC power /s...

Wide 9V to 55V Operating Input Range with TVS protection 3x independent Step-Down Voltage Regulators BEC Vx,  5.2V / 6V / 8V output options.  supp...

Specifications 9V to 55V Operating Input Range Vx for servos,  5V, 6V, 8V Adj. Default is 5V. Synchronous switching step-down (buck) regulator w...

FEATURES High Efficiency Synchronous Step-down regulator Wide 2-8S (6-30V) Operating Input Range Continuous load current: 1.5 Amps (Max....

UBEC DUO 4A/5~12V & 4A/5V This device is a high-efficiency, switch-mode buck regulator with two output channels. It works with 7~26Vdc input. ...

Descriptions. This cable conects betweeen any PL-xxx sensor to the Hub X2-V2, or any BEC from from the PL and PC Series.

Larger Pitot Tube Screw mounting with tube Specifications Pitot Tube M3x10 screws 1m Tube

PREORDERS OPEN NOW - Stock arriving 23 April 2019 Set of four arms for the Micro Alien Frame Can use up to a 3" prop with these arms. 

Mini Carrier Board has the standardized DF17 connector which allows user to connect it to every version of the Cube flight controller. With smaller...

Video cable for DJI O3 air unit.

MMCX 90 Deg male to MMCX Straight Male 8cm lead

Features: Motor wire protectors to prevent from prop strikes. There are different lengths for our iFlight BNFs: 65mm: F5D and F6D rear Arms Chim...

Brand: Amass (Original Manufacturer) Body Material and Surface Plating: Brass and gold plated Insulation Material: PA66 Original Internal Resista...

Rated voltage: DC500V Rated  current: 30A Peak current: 60A Contact Resistance: 0.50mΩ  Metal material: Brass, gold plated Plastic material: PA...

Connector Type: 3 pin 3.5mm bullet plug. Weight: 9.6g per pair (including sleeves).

Details A set of 2 HQ propellers, 2 blade style with a 6mm center hub. They come with a set of plastic reducers (3,4,5,6 mm). They come in sets ...

This is the second generation Goober Canopy that works with 14x14 size fpv camera. As long as the camera board size comes with 14X14 and side scre...

The frame features a traditional look and geometry to maintain the flight characteristics familiar to users, ensuring easy compatibility with the B...

This is a set of 8 nylon standoffs, in a hexagonal shape (25mm). Threaded on both ends for a M3 screw.What's included8x nylon 25mm standoffs

This is a set of 8 nylon standoffs, in a hexagonal shape (35mm). Threaded on both ends for a M3 screw.What's included8x nylon 35mm standoffs

Quality Deans connectors

Aluminium roll cage for the Obsession frame (x1)

Bottom plates for the V2 Obsession frame (2x)

FPV camera side plates for the Obsession frame (x2)