Discountable

Matek's H743-WING V3 Flight Controller arrives with new features and improvements over the original. This FC features a STM32H743VIT6 MCU running ...

The Matek H7A3-SLIM Flight Controller features STM32H7A3VI, ICM20602 & MPU6000, DPS310, OSD, 7x UARTs, 2x I2C, 1xCAN, 13x PWM outputs, BEC5V an...

Specifications Hall effect current sensor No voltage drop and heat on current sensor components Offset and Sensitivity are calibrated in factory C...

Get the voltage you need with this Matek BEC, convert 6-25V to either 5V, 9V, or 12V. This BEC defaults to 5V, select either 9V or 12V by solderin...

Specifications Optical Flow: PMW3901 Lidar: VL53L0X Interface UART Protocol: MSP Working Range: 8cm~200cm Field of view: 42 degree(PMW3901), 27 d...

PDB Input voltage range: 6~60V (2~12S LiPo) PDB/current sense resistor: 140A cont, 264A burst. ESC power pads: 60A cont. 100A burst 6x ESC power /s...

Wide 9V to 55V Operating Input Range with TVS protection 3x independent Step-Down Voltage Regulators BEC Vx,  5.2V / 6V / 8V output options.  supp...

Specifications 9V to 55V Operating Input Range Vx for servos,  5V, 6V, 8V Adj. Default is 5V. Synchronous switching step-down (buck) regulator w...

FEATURES High Efficiency Synchronous Step-down regulator Wide 2-8S (6-30V) Operating Input Range Continuous load current: 1.5 Amps (Max.2.5A 5s/min...

FEATURES High Efficiency Synchronous Step-down regulator Wide 2-8S (6-30V) Operating Input Range Continuous load current: 1.5 Amps (Max....

UBEC DUO 4A/5~12V & 4A/5V This device is a high-efficiency, switch-mode buck regulator with two output channels. It works with 7~26Vdc input. ...

9CH INTL and 2CH US version have identical hardware and layout,  2CH is locked to 1258 & 1280MHz by firmware. Features & Specifications ...

CANPDB w/ 4A BEC & JST-GH Splitter Specifications 6V to 55V Operating Input Range(2S-12S Li-xx) 5.2V output on “5V” pin/pads Suppor...

The Matek Digital Airspeed Sensor ASPD-DLVR features CAN JST-GH connector, UAVCAN Protocol UART1, UART2, UART3 among many other cool features! Spe...

M9N-G4-3100 is based on ArudPilots’ AP_Periph firmware,  It is a GNSS+COMPASS peripheral with CAN/DroneCAN and UART/MSP interfaces. M9N-G4-3100 us...

Power Module PM12S-4A Specifications Wide 9V to 55V Operating Input Range with TVS protection 2x independent Step-Down Voltage Reg...

I2C-INA-BM is an ultra-precise digital power monitor based on TI INA228. The resistance of this conductive path is 200 μΩ typical, providing low p...

200A - Current / Voltage measurement sensor board, based on Allegro Hall Sensor ACS758-200U.Voltage range is up to 20S (85V) with solder bridge ope...

GeneralThe HYB-BEC (Hybrid BEC) is an switching power supply and in the output stage a series linear voltage regulator (LM1764A) to remove the ripp...

Descriptions. This cable conects betweeen any PL-xxx sensor to the Hub X2-V2, or any BEC from from the PL and PC Series.

Larger Pitot Tube Screw mounting with tube Specifications Pitot Tube M3x10 screws 1m Tube

Latest appearance of 65mm 1S brushless frame for Meteor65 Brushless Whoop Quadcopter. With a marvellous design on battery slot which keeps a low pr...

Want a 1S whoop outdoor, around the house and yard, like the 2S 75X or Mobula75 in 2018 winter? Look no further!BetFPV Meteor75 is all you need.1S ...

PREORDERS OPEN NOW - Stock arriving 23 April 2019 Set of four arms for the Micro Alien Frame Can use up to a 3" prop with these arms. 

The Micro-Nano Module Adapter is designed to connect modules with a Nano port to the JR/Micro port's Radio transmitter. Notably, it supports the r...

Mini Carrier Board has the standardized DF17 connector which allows user to connect it to every version of the Cube flight controller. With smaller...

Video  cable for DJI o3 air unit

Video cable for DJI O3 air unit.

SERVO SPECIFICATION Torque (kg-cm) 6.0 (4.8V) / 7.5 (6.0V) / 9.2 (7.4V) / 10.2 (8.2V) Torque (oz-in) 83.3 (4.8V) / 104.2 (6.0V) / 127.8...

SERVO SPECIFICATION Torque (kg-cm) 6.0 (4.8V) / 7.5 (6.0V) / 9.2 (7.4V) / 10.2 (8.2V) Torque (oz-in) 83.3 (4.8V) / 104.2 (6.0V) / 127.8 (7...

MMCX 90 Deg male to MMCX Straight Male 8cm lead

Spare Parts-X500 V2 Kit

Features: Motor wire protectors to prevent from prop strikes. There are different lengths for our iFlight BNFs: 65mm: F5D and F6D rear Arms Chim...

JX6 Quick Release Connector Male/Female MPX Connector Model: JX-6Metal material: gold-plated brassPlastic material: PAInstantaneous current: (large...

Specification Weight: 9.5g/pair Type：JX-9 Metal Material: Brass Gold Plated Plastic Material: PA Instantaneous current: (big) 60A/(Small) 7A Rated ...

Finally a purpose built FPV earbud that we have engineered from the ground up to favor sound quality from onboard microphones! We hand-selected th...

Brand: Amass (Original Manufacturer) Body Material and Surface Plating: Brass and gold plated Insulation Material: PA66 Original Internal Resista...

Rated voltage: DC500V Rated  current: 30A Peak current: 60A Contact Resistance: 0.50mΩ  Metal material: Brass, gold plated Plastic material: PA...

Connector Type: 3 pin 3.5mm bullet plug. Weight: 9.6g per pair (including sleeves).

Details A set of 2 HQ propellers, 2 blade style with a 6mm center hub. They come with a set of plastic reducers (3,4,5,6 mm). They come in sets ...

This iFlight BNF Nazgul Evoque F5D V2 HD features the DJI Camera.  We also carry the iFlight BNF Nazgul Evoque F5X HD. The new iFlight Nazgul Evoqu...

This is the second generation Goober Canopy that works with 14x14 size fpv camera. As long as the camera board size comes with 14X14 and side scre...

The frame features a traditional look and geometry to maintain the flight characteristics familiar to users, ensuring easy compatibility with the B...

This is the second generation Goober Canopy that works with 14x14 size fpv camera. As long as the camera board size comes with 14X14 and side scre...