support@flyingrobot.co.za
support@flyingrobot.co.za
Save 0%
Save %
M9N-5883 uses multi-constellation GNSS powered by u-blox NEO-M9N , NEO-M9N is a concurrent GNSS receiver which can receive and track multiple GNS...
View full details
Save 0%
Save %
Matek's H743-WING V3 Flight Controller arrives with new features and improvements over the original. This FC features a STM32H743VIT6 MCU running ...
View full details
Save 0%
Save %
The Matek H7A3-SLIM Flight Controller features STM32H7A3VI, ICM20602 & MPU6000, DPS310, OSD, 7x UARTs, 2x I2C, 1xCAN, 13x PWM outputs, BEC5V an...
View full details
Save 0%
Save %
Specifications Hall effect current sensor No voltage drop and heat on current sensor components Offset and Sensitivity are calibrated in factory C...
View full details
Save 0%
Save %
Get the voltage you need with this Matek BEC, convert 6-25V to either 5V, 9V, or 12V. This BEC defaults to 5V, select either 9V or 12V by solderin...
View full details
Save 0%
Save %
PDB Input voltage range: 6~60V (2~12S LiPo) PDB/current sense resistor: 140A cont, 264A burst. ESC power pads: 60A cont. 100A burst 6x ESC power /s...
View full details
Save 0%
Save %
Wide 9V to 55V Operating Input Range with TVS protection 3x independent Step-Down Voltage Regulators BEC Vx, 5.2V / 6V / 8V output options. supp...
View full details
Save 0%
Save %
Specifications 9V to 55V Operating Input Range Vx for servos, 5V, 6V, 8V Adj. Default is 5V. Synchronous switching step-down (buck) regulator w...
View full details
Save 0%
Save %
FEATURES High Efficiency Synchronous Step-down regulator Wide 2-8S (6-30V) Operating Input Range Continuous load current: 1.5 Amps (Max....
View full details
Save 0%
Save %
UBEC DUO 4A/5~12V & 4A/5V This device is a high-efficiency, switch-mode buck regulator with two output channels. It works with 7~26Vdc input. ...
View full details
Save 0%
Save %
The Matek Digital Airspeed Sensor ASPD-DLVR features CAN JST-GH connector, UAVCAN Protocol UART1, UART2, UART3 among many other cool features! S...
View full details
Save 0%
Save %
M9N-G4-3100 is based on ArudPilots’ AP_Periph firmware, It is a GNSS+COMPASS peripheral with CAN/DroneCAN and UART/MSP interfaces. M9N-G4-3100 us...
View full details
Save 0%
Save %
Power Module PM12S-4A Specifications Wide 9V to 55V Operating Input Range with TVS protection 2x independent Step-Down Voltage Reg...
View full details
Save 0%
Save %
PM20S-2 is made with 100V DC components. Support 9V to 85V DC operating Input voltage with 85V TVS protection 2x independent Step-Down Voltage Reg...
View full details
Save 0%
Save %
I2C-INA-BM is an ultra-precise digital power monitor based on TI INA228. The resistance of this conductive path is 200 μΩ typical, providing low p...
View full details
Save 0%
Save %
Descriptions. This cable conects betweeen any PL-xxx sensor to the Hub X2-V2, or any BEC from from the PL and PC Series.
Save 0%
Save %
Save 0%
Save %
PREORDERS OPEN NOW - Stock arriving 23 April 2019 Set of four arms for the Micro Alien Frame Can use up to a 3" prop with these arms.
Save 0%
Save %
Mini Carrier Board has the standardized DF17 connector which allows user to connect it to every version of the Cube flight controller. With smaller...
View full details
Save 0%
Save %
Save 0%
Save %
Video cable for DJI O3 air unit.
Save 0%
Save %
MMCX 90 Deg male to MMCX Straight Male 8cm lead